Search found 11 matches
- Wed Feb 05, 2014 1:04 am
- Forum: EIS Sensors
- Topic: Oil Temp Not Working
- Replies: 2
- Views: 9115
Re: Oil Temp Not Working
I did. There was an issue with the EIS. I sent it back to GRT for repair and it's working great. I don't have any details on what the issue was with the EIS box. If you have tried all the test I did mentioned previously in the post, you may want to talk to GRT about sending back. Hope this helps...
- Tue Oct 29, 2013 9:25 pm
- Forum: Show Us Your Panel
- Topic: F1 Rocket with Dual Hx Displays
- Replies: 1
- Views: 12304
- Sun Jul 07, 2013 1:38 am
- Forum: Horizon HX
- Topic: General Setup - Flight ID & Address
- Replies: 2
- Views: 7517
- Sun Jul 07, 2013 12:29 am
- Forum: Horizon HX
- Topic: General Setup - Flight ID & Address
- Replies: 2
- Views: 7517
General Setup - Flight ID & Address
I noticed in the General Setup entries for Flight ID & Address. I could not find anything in the manual for documentation on these settings. Is the Flight ID the N-number of aircraft, and, Address the Mode S code assigned to airplane (hex on octal?) for ADS-B?
Thanks.
Thanks.
- Sun Jul 07, 2013 12:04 am
- Forum: EIS Sensors
- Topic: Fuel Pressure Not Working
- Replies: 0
- Views: 25143
Fuel Pressure Not Working
I ran the engine for the first time and discovered that I am not getting any indication of fuel pressure on the EIS or HX EFISs. I have the 80psi VDO type sensor. This was confirmed by GRT a few months back when I gave them the part number. The fuel pressure reading is -0.4 psi with the engine off, ...
- Sat Jul 06, 2013 11:52 pm
- Forum: EIS Sensors
- Topic: Oil Temp Not Working
- Replies: 2
- Views: 9115
Oil Temp Not Working
I ran my engine for the first time and discovered that the Oil Temp was not working on the EIS or HX EFIS's. Here is what I have done thus far in an attempt to figure out the problem. 1. I have verified that there is continuity from EIS D-sub connector Pin 15 to the Oil Temp Sensor. 2. I have a good...
- Sun May 19, 2013 1:26 am
- Forum: Horizon HX
- Topic: Engine Performance Table Setup
- Replies: 3
- Views: 8427
Re: Engine Performance Table Setup
Thanks Jeff...
- Fri May 17, 2013 1:50 am
- Forum: ADS-B/Weather/Traffic
- Topic: NavWorx ADS-B Setup with Hx
- Replies: 6
- Views: 15419
- Fri May 17, 2013 1:46 am
- Forum: Horizon HX
- Topic: Engine Performance Table Setup
- Replies: 3
- Views: 8427
Engine Performance Table Setup
I am working on the engine performance table setup (Hx Setup and Config Guide pg 6-6) so the EFIS can calculate % Power. I am skeptical that I created the table correctly. Does anyone have a performance table for a IO540 D model that works well they would share?
Thanks..
Thanks..
- Mon May 13, 2013 2:29 am
- Forum: ADS-B/Weather/Traffic
- Topic: NavWorx ADS-B Setup with Hx
- Replies: 6
- Views: 15419
NavWorx ADS-B Setup with Hx
I have a NavWorx ADS-B and a dual display Hx system. The NavWorx RS232 Display Serial Data Input (Pin 24), and, the RS232 Display Serial Data Output (Pin 5) are connected to display unit #1 Serial 7 In and Serial 7 Out. When I am in the General Setup for Display Unit #1, what baud rate and value sho...