Search found 14 matches
- Thu Jul 24, 2014 3:11 pm
- Forum: EIS Sensors
- Topic: CS-01 or CS-02 physical installation
- Replies: 0
- Views: 24789
CS-01 or CS-02 physical installation
How does one physically mount the CS-02 or CS-01? I have the CS-02, the small sized one, on a firewall wire. I have run the wire through it OK, but the sensor is awkward to secure. The stem is at a right angle to the hole and I have tied it to nearby wires. Do I use some E6000 and glue the wire goin...
- Wed Jun 25, 2014 5:42 pm
- Forum: Horizon HXr
- Topic: AHRS power
- Replies: 9
- Views: 20434
Re: AHRS power
Eric Your idea of one power feed and suppling both units if fine but, You might want to consider to supply your EFIS and AHRS via two power inputs since you have a E bus. Both the EFIS and AHRS has 3 power inputs. Run one power input to each via your avionics supply controled by avionics switch off...
- Wed Jun 25, 2014 4:50 pm
- Forum: Horizon HXr
- Topic: AHRS power
- Replies: 9
- Views: 20434
Re: AHRS power
Remember the fuse protects the wires. Use large enough wires so that one won't turn into a toaster at the maximum current allowed by tbe fuse. Dear Bobturner, This is from the HXr Install Manual: >The display units consume approximately 1 amp >Power supplied to the EFIS must pass through an externa...
- Tue Jun 24, 2014 11:15 pm
- Forum: Horizon HXr
- Topic: AHRS power
- Replies: 9
- Views: 20434
Re: AHRS power
Why not just run a #18 wire to the same switch/CB as the HXr? Bob, Because that would be too simple and make too much sense. I'm thinking a 22awg wire because that is what is pre-supplied by GRT for the AHRS primary power input wire. Thank you for the answer, Eric Bob, I called GRT and per Ben, a s...
- Mon Jun 09, 2014 3:29 pm
- Forum: Horizon HXr
- Topic: AHRS power
- Replies: 9
- Views: 20434
Re: AHRS power
Why not just run a #18 wire to the same switch/CB as the HXr? Bob, Because that would be too simple and make too much sense. I'm thinking a 22awg wire because that is what is pre-supplied by GRT for the AHRS primary power input wire. Thank you for the answer, Eric Bob, I called GRT and per Ben, a s...
- Mon Jun 09, 2014 3:04 pm
- Forum: Horizon HXr
- Topic: AHRS power
- Replies: 9
- Views: 20434
Re: AHRS power
Bob,Bobturner wrote:Why not just run a #18 wire to the same switch/CB as the HXr?
Because that would be too simple and make too much sense.
I'm thinking a 22awg wire because that is what is pre-supplied by GRT for the AHRS primary power input wire.
Thank you for the answer,
Eric
- Sun Jun 08, 2014 5:15 pm
- Forum: Horizon HXr
- Topic: AHRS power
- Replies: 9
- Views: 20434
AHRS power
I need some help figuring out the wiring as I Install the AHRS in my HXr system. Per the Pin Out Description, the primary AHRS power input port is Pin 23 on the connector and the input is referred to as Aircraft Power Input A. In the Installation Manual is a note saying the Display and AHRS should b...
- Sun Jun 08, 2014 4:25 pm
- Forum: Show Us Your Wiring Diagrams
- Topic: RV-7A Wiring Diagram
- Replies: 1
- Views: 12472
Re: RV-7A Wiring Diagram
Mr Casey,
Tried to follow the dropbox link, but it appears to broken.
Regards,
Eric Schlanser
Tried to follow the dropbox link, but it appears to broken.
Regards,
Eric Schlanser
- Sat Jan 25, 2014 10:44 pm
- Forum: EIS Sensors
- Topic: Oil Pressure sender ground
- Replies: 1
- Views: 6638
Re: Oil Pressure sender ground
Found a solution on the MGL site. I cant figure out how to insert insert an image so here is a link to a picture on the MGL site. I'm not sure what they mean by brazing a terminal on the sender. I did mine by soldering a quick connect tab to the sender case. http://kb.mglavionics.com/article/AA-0032...
- Fri Jan 24, 2014 9:17 pm
- Forum: EIS Sensors
- Topic: Oil Pressure sender ground
- Replies: 1
- Views: 6638
Oil Pressure sender ground
"Ground is normally provided by the engine when the sensor is mounted directly to it, but a separate ground wire may be necessary for remote installations", says the EIS manual in paragraph 5.2.4 for installation of the VDO oil pressure sender. Can I get a little more detail on how the sep...